Newtonsoft.Json.JsonReaderException: Error reading JArray from JsonReader. Path '', line 0, position 0. Depends what type of circular saw and the size of blade/teeth. Too course and it will shatter the laminate. If you’re able to, use a drill bit one size smaller than the screws. It creates small pilot holes that hold the screws more firmly in place. If the holes are too big, the screws won’t stay in. Fit the gravel boards into the slots on the posts. Make sure all of the fence panels are out from between the posts. Install the boards by lifting them up and sliding them into the slots on the posts. They can be pretty heavy, so ask a friend to lend a hand. Push them firmly against the ground to ensure they are stable and level. [8] X Research source

Or bodge it and ‘glue’ them in place with silicone and wind feet down tight onto floor - they ain’t gonna moveUse a bubble level to make sure the boards are even. Test the boards one by one. Set the level on top of one of the boards, then watch the liquid capsule in its middle. It has a bubble that will shift to one side, depending on which one is higher. Make adjustments to each board until they are all level. [9] X Research source Measure the available space between the fence posts. Stretch a tape measure from one post to the other to determine the length of each section. This measurement is useful for cutting the boards to the proper length. Then, measure from the ground-up to determine how tall you want the gravel boards to be. The gravel boards usually do not need to be thinned at all, so it’s better to avoid doing this unless absolutely necessary. [4] X Research source For example, if you have a stretch of ground 48 ft (15 m) long, you could use 8 posts spaced 6 ft (1.8 m) apart. That way, each part of the fence will be equal. You could also space 6 posts 8 ft (2.4 m) apart. Tesco Mobile is to start charging new and recently joining pay-monthly customers to use their mobiles in Europe from 2024.

Use a masonry drill bit to make 7 mm (0.28 in) holes in the posts. Plan on making the pilot holes roughly the same size as the screws you’re using. Fit the bit on a power drill, then carefully drill through the spots you marked. Make each hole about 7 mm (0.28 in) deep, or about the same length as the screws you’re going to use. [15] X Research source Turbo boost your credit chances and get your free Experian credit report. Credit Card & Loans Eligibility Calculator Beauty Advent calendars are significantly pricier than chocolate ones, but they've become increasingly popular in the last few years as a way of bagging beauty products at a fraction of the normal cost. They often sell out early, but can also be heavily discounted later if they don't, so here's a round-up of some of the best I’ve seen. So add 50mm + 18mm for plinth + 25mm (half the width of the 3 x 2" . This gives you93mm. This should ensure you hit the dead centre of the wood. Drill your holes 93mm from front of unit. Countersink.From googling, I've read that a circular saw should be fine for cutting through the laminate (it's a gloss finish). I'm not sure if we have one of these. What other materials would be OK to use so I don't chip the laminate?

If you do not feel confident in being a DIY-er, or would prefer to not use your time on a project like this, get in touch with a professional to make your life easy and complete the job in a timely and skilful way.

If you've got a Marcus easy-access savings account or cash ISA, you can easily boost your interest rate to 4.75% – here's how. You can cut rails out of pine or cedar wood boards. Trim them to the same length as the gravel boards. Place one in the center of the fence, then another along the top. If you're a regular Superdrug shopper, you can now earn more freebies and discounts under its Health & Beautycard loyalty scheme, as the retailer has launched new 'VIP Rewards' as part of it. The boards are available online and at many hardware stores. They can also be bought from fencing companies. You will need 2 clips for each gravel board you plan on installing. If you have a 48 ft (15 m) fence with 7 gravel boards, get 14 clips.

You can often assemble the fence panels on the ground, then lift the entire panel up and slot it onto the posts. Slotted fencing is often very easy to install! Install the gravel boards by sliding them into the clips. Make sure all of the fence panels are out of the way. Then, lift them and fit them into the open clips. Push each board as far down as you can. Once the boards are in place, you can begin assembling the fence panels. [17] X Research source Without being able to see how the plinths are attached, my guess would be that the clips are possibly a spring loaded type which will have a specific way to release it , ie a blade inserted etc, If you’re fitting boards on a single length of fence with multiple posts, you usually won’t need to measure more than 1 section. Unless the fence posts were placed incorrectly, they will be spaced evenly.Fine teeth in the saw for sure, and I'd use tape across the cutline while cutting to make sure the edge is as clean as possible. Instead of shortening the gravel boards, use shorter panels on your fence. You could also cut existing fence panels shorter to ensure your fence is at the height you desire. Either screw up into base of cabinet using a short stubby screwdriver or a right angled drill attachment